You've got something about you
We've got something you need
Taper of the Trade
See this set and take heed

The Asgard "God of Thunder" Taping Set has all your taping essentials perfect for the "God of Taping"! This set includes:

• Asgard "The Hammer" Automatic Taper
• Mud Pump With Filler Adapter
• Gooseneck
• 10" & 12" Flat Box
• Brakeless Extendable Flat Box Handle
• 2.5" & 3" Angle Head
• 8" Corner Box With Handle
• Inside Corner Roller
• Extendable Support Handle

The Asgard® Nail Spotter is used to fill the depressions left from the nails or screw heads during installation of the drywall. The Nail Spotter features an easy clean box design that removes excess compound at the same time as filling the depressions. The hardened steel skid plate allows the Nail Spotter to move along the wall smoothly while protecting the stainless steel blade from nail or screw heads that were not fully set below the surface of the drywall. The NS01-AD Nail Spotter attaches to the XH-AD extension handle or FH-AD fiberglass handle (sold separately). The Nail Spotter is also used to quickly identify fasteners that were not properly set during the installation of the gypsum board. Before starting to apply joint tape, run the Nail Spotter over all the fasteners (walls and ceilings). If you hear a “click”, the fastener should be set deeper to avoid damage to the other tools. You can also use the Nail Spotter to apply joint compound to the outside edges of internal corners. This is a quick and efficient way to clean up any edges that may have been left by the Angle Heads due to corners that are slightly out of square.

• Fills depressions left from the heads of nails or screws in drywall
• Removes excess joint compound after filling dimples
• Quickly identifies improperly set fasteners

Asgard® Tools feature an interchangeable handle system that allows one support handle to be used with the Corner Applicator, Corner Roller and Nail Spotter without additional adapters. To attach the support handles to the Angle Heads, use the CFA-AD adapter. The FH-AD support handle is lightweight but robust and its optimal diameter makes it extremely ergonomic. The D-shaped fitting securely positions the handle in the Corner Applicator to prevent the tool from rotating during use.

• Supports the Corner Applicator, Corner Roller, Nail Spotter and Angle Head (with CFA-AD adapter)

Asgard® Tools feature an interchangeable handle system that allows one support handle to be used with the Corner Applicator, Corner Roller and Nail Spotter without additional adapters. To attach the support handles to the Angle Heads, use the CFA-AD adapter. The XH-AD extendable support handle features robust construction and its optimal diameter makes it extremely ergonomic. The XH-AD extends from 43” to 76” (106 cm to 193 cm). The D-shaped fitting securely positions the handle in the Corner Applicator to prevent the tool from rotating during use.

• Attaches to Corner Roller, Corner Applicator, Nail Spotter and Angle Heads (with CFA-AD adapter)

The Asgard® CA08-AD Corner Applicator supplies joint compound to the Angle Heads for fast and efficient finishing of internal corners (angles). The CA08-AD Corner Applicator features a stainless steel cone and a D-Shaped adapter to prevent rotation. Use with the FH-AD or XH-AD Support Handle – not included.

• Finishes internal corners (with Angle Heads)

The Asgard® Adjustable Angle Head is used to perfectly feather the joint compound applied to both sides of internal corners in one pass. The Angle Head can be used for wall-to-wall internal corners or wall-to-ceiling corners. The “adjustable” feature of this tool refers to the ability to control the amount of spring pressure by engaging or disengaging one set of tension springs on the back of the angle head. Angle Heads, also referred to as Angle Finishers or Corner Finishers, are attached to the CA08-AD corner applicator to quickly and professionally finish internal drywall corners. The 3” Asgard Angle Head has wheels to provide the smoothest action on the wall and are spring loaded to help compensate for slightly imperfect corners. The Angle Head is also used as part of the Taping process when attached to the FH-AD or XH-AD support handles with the CFA-AD adapter.

• Embeds joint tape in internal corners of walls and ceilings
• Finishes internal corners of walls and ceilings
• Wipes down excess joint compound in internal corners

The Asgard® Power Assist® Finishing Box requires 50% less effort to automatically dispense the proper amount of joint compound and feather the edges of butt joints and flat joints in one pass. Simply place the blade on the joint first then apply the wheels to activate the Power Assist mechanism. The Power Assist® finishing boxes from Asgard® provide the extra capacity you want with half the effort required from other high capacity finishing boxes. The adjustable crown setting dial allows you to easily adjust the amount of joint compound applied over the tape on the drywall joint. This is very helpful when progressing from the first embedding application to the second or third finishing coat. The pivoting axle helps to compensate when the gypsum board on one side of the joint is higher than the other side of the joint.

• Applies first coat of joint compound to embed tape at butt joints and flat joints on walls and ceilings
• Finishes butt joints and flat joints on walls and ceilings
• Feathers edges of butt joints and flat joints

The Asgard® MAXXBOX® Finishing Box automatically dispenses the proper amount of joint compound and feathers the edges of butt joints and flat joints in one pass. The MAXXBOX® Finishing Box helps produce professional results every time. The adjustable crown setting dial allows you to easily adjust the amount of joint compound applied over the tape on the drywall joint. This is very helpful when progressing from the first finishing application to the second or third application. The pivoting axle helps to compensate when the gypsum board on one side of the joint is higher than the other side of the joint. Asgard® MAXXBOX® Finishing Boxes are designed with the optimum capacity to weight ratio. This means that you get more “usable” joint compound – the amount that you can actually get out of the finishing box and onto the wall – when you actually need it, like on the first coat over the joint tape. The Asgard MAXXBOX® finishing box delivers 60% more usable joint compound than the standard Classic finishing box (model EZ10-AD) and up to 36% more usable capacity than competitive high capacity finishing boxes.

• Applies first coat of joint compound to embed tape at butt joints and flat joints on walls and ceilings
• Finishes butt joints and flat joints on walls and ceilings
• Feathers edges of butt joints and flat joints

Exclusive Bart's Taping Tools Set.

Includes:

• 10" & 12" Flat Boxes
• Extendable Brakeless Handle
• Mud Pump With Filler Adapter